Tag Archives: bracket feet

3 Accepted Foot-to-Case Connections

Last week, after I professed that everyone should have a spindle sander, A few readers asked how I used a spindle sander as a thickness sander. It turns out that I have posted that technique, but it was inside another post. Here’s a link to that post; you’ll find the spindle sander being used to thin ebony string about halfway down the post.

Entertainment_Center copyOn to the next topic: How to attach feet to your case. Of course, there are a few ways to get feet on your cases. There are three methods I generally use on most every case. The first is to attach the feet directly to the bottom of the case, a second method is to rout the top edge of the joined feet and install a plate through which screws affix the assembled unit to the case bottom and the third method is to attach feet to a frame then attach the frame to the case and use a transition molding to cover the through dovetails where the case bottom joins the sides. I mention other methods, because I’ve built a couple of chest – full-size and spice boxes – from Chester County where the feet were attached directly to stiles of the frame and panels sides. While this is not commonplace, it, along with other methods, is sometimes done.

To attach feet directly to the case, I begin by installing a molding to which the feet are glued. You wouldn’t think that you could assemble feet to a molding and that would be strong enough to hold everything for 200 years. IMG_1590Of course, you would be correct. What really holds the feet to the case are  glue blocks. These blocks also carry the bulk of the load of your chest. On the case I’m currently at work on, the thickness of the feet allows about an 1/8″ of the feet to lap onto the case itself. Then, with the glue blocks in place, the weight of the case is divided on the actual feet and on the glue blocks – the vertical block holds the weigh while the two horizontal blocks keep the assembled foot attached.

The next method is a bit more work. And the added plate makes the connection easier, but not necessarily any stronger. After the two foot pieces are joined via miters, I rout a small lip on the inside of the feet using a rabbeting router bit to which I attach a thin plate. PlateThe SketchUp drawing at the left shows how the plate fits to the feet; a thin bead of glue and brads secure the plate to the feet. The assembled unit is then screwed directly to the case bottom with the unit sticking out in front of the case. The look is completed by wrapping a molding around the case. An example of this type of connection is seen in the opening photo, although you cannot see the plate. That’s by design. As you see in the drawing, the cutout for the plate does not blow through the end of the foot.

The last method – the option that I find the most used as I look back at furniture I’ve built throughout the years – is to attach the feet to a base frame which is then attached to the case. Foot&Frame3I used this method on the Pennsylvania blanket chests in the August 2009 issue of Popular Woodworking Magazine (#177) and the Serpentine chest from issue #195 (February 2012). As you can see in the right-hand photo, the same idea of glue blocks is used – mainly for reinforcement in this case. The frame is attached to the front of the chest with screws, but the remaining frame is nailed to the case bottom to allow for seasonal adjustments. The look is then completed with a transition molding.

These are three good methods used to attach feet to cases. There are pros and cons to each, as there is with any technique used in woodworking. Whenever you here, “This is the only way to do it,  run in the opposite direction. You have choices.

Build Something Great!

Glen

 

3 Comments

Filed under Joinery, Methods of Work

Shop Shortcuts – Foot Pattern

I do a lot of work with patterns. Most often, my patterns are used to guide a router bit (top-mounted bearing) to finalize a profile. But the pattern shown here is used only for layout.

IMG_1578When building any chest of drawers that has bracket or ogee bracket feet, I make a pattern for the foot. I use six individual feet for the show sides of most chests, with the two rear feet being a more plain design and usually made out of secondary woods. To make my fancy feet, I could simply use a paper pattern to layout the design, but my pattern would be in shambles as I worked on the sixth foot. Another option would be to print six copies of the design then glue each paper to a foot blank before going to the band saw to cut out the designs. I, however, make a pattern using scrap 1/4″ plywood which holds up to not only the six uses on this chest, but will be around the shop if I make a second or third chest, and will be standing at the ready for a completely different future chest if the design was right.

IMG_1573Here’s the process in case you’re not yet a pattern maker. I pull a paper pattern out of my SketchUp drawing (you could, of course, lay out the foot using pencil, compass and straightedge), cut it out then stick it to the plywood with spray adhesive. Then it’s off to the band saw to trim to the lines. Be close, but don’t hit the lines. And more important, don’t cut away the circle at the center of the foot that helps form the spur. We need that area later in the process.

IMG_1575After working at my band saw, my next step is at the spindle sander. After you have the correct spindle installed, work to your layout lines. Again, leave the lines intact. If you don’t have a spindle sander (see below), you can file and rasp your way to a great design.

Why would you not have an inexpensive spindle sander in your shop? Even the cheap machines last forever – I still have a Ryobi spindle sander from 15 years ago that I take to classes and seminars if need be. And there’s a lot that you can do with these simple machines, including thickness-sanding inlay and veneer.

IMG_1577The last step to prepare the foot pattern for work is to find and create the center point of the waste area the forms the spur. On all my feet, this waste to drilled out using a Forstner bit at my drill press. To find the center point, position the pattern under your drill bit until the circle is perfectly centered, then plunge down to leave a mark. I then drill down about a 1/16″ to set the waste area and just puncture through the pattern. The last step before putting this shop-made template to work is to completely pierce the plywood with a small drill bit.

The opening photo shows how the pattern is used. I’ll add a word of caution here. If you’re foot stock is a bit less than desirable on the rear face, make sure you flip the pattern as you work – lay out three feet facing left and three facing right. That way you can produce pairs that all show the correct face forward. And this is something you have to do if you’re using these patterns for ogee-bracket feet.

Build Something Great!

Glen

 

6 Comments

Filed under Jigs, Methods of Work, Shop Tips